Liminal Nomad
3D printed chassis weights designed to solve the problem of attaching external weights to chassis where the M-LOK to ARCA rail distance is shorter than normal (Aero Solus and Outlier Modular) while retaining full use of the integrated ARCA rail.
Due to the reduced distance between the ARCA rail and M-LOK slots on chassis like the Aero Solus most chassis weights won’t be compatible when using an ARCA adapter like the Area 419 ARCALOCK Clamp. So the profile of this weight was designed to not interfere with twist knobs on these clamps even when on the clock.
Will work on more standard spacing like those chassis made MDT, MPA, KRG, XLR, etc or M-LOK forends found on AR platforms. Just like any other weight this will help to reduce felt recoil, and tune a rifle’s balance. The extra width these add to a chassis also increases surface contact with a front bag making for a more stable platform.
Features:
Diamond texture top surface for better purchase
Lead shot fill has slight dead blow hammer dampening effect
Integrated recoil lugs
Lid cover screws are same thread and length as Solus adjustable magazine catch screws if you loose one during a match. Can temporarily be used with one lid screw missing in that case.
Tested at multiple +100° F matches
Rad translucent colors (photos incoming)
Weight:
11.29 Oz per set
Material:
PETG+ body
Lead shot fill
Stainless steel black oxide hardware
Tools needed for installation:
1/8” Hex for M-LOK screws
5/64” Hex for lid screws
The goal of this front bag was to enhance the stability of your rifle while it’s on the bag vs other front bags.
Utilizing a V shaped top surface allows the bag and filling to make a channel, creating more surface contact with the fore end of your rifle. That means you end up with more stability before you break your shot.
During the recoil phase it helps to make the recoil impulse as linear (less lateral jump) as possible, making it much easier to see your hits.
If you flip it over, say to shoot off a rock or flatter prop, you get a larger surface area contacting the prop as well. Neither orientation limits traversing very wide angles.
While the Twisted X is designed for and excels at positional long range shooting events (PRS, NRL Hunter, NRL22, etc) they are also perfect for any other use where you want an ultra stable bag to shoot off.
Trapezoidal prism shaped to improve stability when you want the most height out of it but still having a slim option when you only need an inch or so to rest the buttstock on.
Large loop for putting your hand through, or clipping to your backpack.
Velcro + roll top closure if you want to change out or lessen the fill. Shipped with more fill than recommended so you can adjust to your preference.
A bag rider for Magpul® ACS® & STR® stocks focused towards the needs of long range and precision shooting.
At less than 1oz it has as little impact on center of balance as possible, making it easier to achieve an optimal balance point. I having a surface area comparable to many precision chassis systems it gives a larger contact point and better ability to adjust your stock to rear bag interface with as little fiddling as possible
Does not require any additional accessories to add a bagrider for your ACS/STR stock. Compatible with Magpul aftermarket butt pads and Arisaka Stock Angle adapter.
Dimensions:
4”x1”x1”
Weight:
.7 oz / 20 g
Material:
Nylon 11
Tools needed for installation:
1/8” Hex Key
Flat head screwdriver (medium to small)
The best CZ 457 chamber flag and magazine block solution. With PRS22 and NRL22* matches now requiring a chamber flag, this flag block provides a superior ergonomic experience allowing you to keep your attention on cleaning the next stage.
Squeezing the back of the magazine at the Nomad logo retracts the spring loaded chamber flag allowing you to insert it into the mag well. No extra thumb fiddling or extra movement. When removing, the same natural ergonomics of squeezing the magazine release and the back of the magazine pulls out the chamber flag. No need for unnatural thumb movements compromising your grip on the magazine block like other flag block designs.
Features:
Spring loaded chamber flag for maximum safety and ease of use
Cording hole for optional bungee/keeper cord.
Compatibility:
Designed to function with all CZ 457 chassis, and stocks
CZ, MDT , KRG, HBi, XLR, GCP/Vision Gen 2, Grey Birch La Chassis, Ultradyne
Material:
High Temp Polymer (Will not melt, tested in 100+ temps)
Stainless steel hardware
*NRL22 2026/2027 rulebook does not explicitly require a chamber flag (mag blocks ok at the discretion of the MD). But they are strongly recommending all MDs require chamber flag/ device the guarantees an empty chamber.